We all need that assurance that our property is safe. You should not only get insurance but also make sure that you have kept the things themselves in a safe place. This is why when you are especially traveling, you should have your custom road cases. These will always ensure that your property is safe from all kinds of weather.
You need to set up a place where you will be spending most of your time building the case. You should make sure that you have all the equipment you need in order to move the process along faster. Make sure that you have a cut list to avoid wasting any material. You are to build the case according to the size of the item you are building the case for.
After gathering everything you need, you need to get to work. You should start off by cutting the aluminum. Aluminum is not only one of the strongest elements of this case but it is also decorative. That shiny new look gives some elegance to it. It is recommended that It is best to use a cold saw to avoid any kind of damage to the aluminum.
The next step is to make the pockets and notches of the case. These are made out of wood and it should, therefore, be not too difficult to use make them. You will need to mark the cut points and you should, therefore, use the unfinished side of the ABS. Afterward, you should reduce the size of the u-channels to match the sizes of the notches.
For your case to be complete and stand straight, you will need to have corners. This corners not only give the shape but they also ensure that the case has the capacity to hold items inside without fail. These corners do not connect by the use of glue and screws; they actually use rivets to hold them in place. It is recommended to use a pneumatic riveter to put them in place.
You will need to attach the corners to your case. Otherwise, it will just be an undetermined shape. You should hold the corner snug and drill the holes in all the corners then come back around to drill the number of needed holes on each face. These corners are meant to act as absorbers but they at the same time give the case a shape and hide the flaws at the corners.
Depending on what you keep inside, the case may be heavy or light. If it is heavy, you may want it to have a wheeled bottom to push it around. In case it is a light one, you may go for a rubber bottom to protect it from dirt and even moist surfaces. As you assemble the case, it should be in a closed position to avoid placing hinges in the wrong places.
Your case will need a foam interior. This not only makes it look a lot more elegant. You should cut out like half of an inch. You should start from the base upwards. You should ensure that the foam on the walls is shorter than the wall so that the road can close properly.
You need to set up a place where you will be spending most of your time building the case. You should make sure that you have all the equipment you need in order to move the process along faster. Make sure that you have a cut list to avoid wasting any material. You are to build the case according to the size of the item you are building the case for.
After gathering everything you need, you need to get to work. You should start off by cutting the aluminum. Aluminum is not only one of the strongest elements of this case but it is also decorative. That shiny new look gives some elegance to it. It is recommended that It is best to use a cold saw to avoid any kind of damage to the aluminum.
The next step is to make the pockets and notches of the case. These are made out of wood and it should, therefore, be not too difficult to use make them. You will need to mark the cut points and you should, therefore, use the unfinished side of the ABS. Afterward, you should reduce the size of the u-channels to match the sizes of the notches.
For your case to be complete and stand straight, you will need to have corners. This corners not only give the shape but they also ensure that the case has the capacity to hold items inside without fail. These corners do not connect by the use of glue and screws; they actually use rivets to hold them in place. It is recommended to use a pneumatic riveter to put them in place.
You will need to attach the corners to your case. Otherwise, it will just be an undetermined shape. You should hold the corner snug and drill the holes in all the corners then come back around to drill the number of needed holes on each face. These corners are meant to act as absorbers but they at the same time give the case a shape and hide the flaws at the corners.
Depending on what you keep inside, the case may be heavy or light. If it is heavy, you may want it to have a wheeled bottom to push it around. In case it is a light one, you may go for a rubber bottom to protect it from dirt and even moist surfaces. As you assemble the case, it should be in a closed position to avoid placing hinges in the wrong places.
Your case will need a foam interior. This not only makes it look a lot more elegant. You should cut out like half of an inch. You should start from the base upwards. You should ensure that the foam on the walls is shorter than the wall so that the road can close properly.
About the Author:
You can find a detailed overview of the benefits you get when you order custom road cases at http://www.encorecases.com/products right now.
No comments:
Post a Comment