One of the efficient printing techniques in our society is printing from the screen. It does not matter if it is prepared from paper, silk, or other products. However, Maryland screen printing at times might be challenging to armatures. The article will highlight some of the problems that they are likely to face and the best way to deal with them.
If you notice that the paint is spreading through the areas that you do not want to print, then this is known as bleeding. It is one of the most common mistakes that one might find, and the best way that you can deal with it is making the paste thick. Bleeding comes as a result of using watery paste. It is best to ask someone who has been this for a long time to help you with the mixing of the adhesive.
It is frustrating when you find that you have gaps that are not equal when you are doing repeats. Most people think that doing a repeat is something simple, but that is not the case. If you want to do it right then, you should be calculative. Check well and do calculative placement.
If you are new in this scheme, you might not know where to place the repeats. To deal with this, you need to use colored chalk to mark the repeats on that cloth, and this will help one know where they will be placing each repeat. The other solution is placing of colored strands at the edge of the design and when doing a repeat all one need to do is to put the screen directly on the strands.
The other thing that you should watch out for is soiling of the cloth. Note that if you do not block the pores, then you might end up with this problem. That is the reason that you should apply a tape around the edge; it will make the print clean and well done since there will be no spillage on the sides.
Having the colored pigments not being distributed is also another issue that you might end up facing. If this is the situation, you might end up with the formation of patches. If you want to have a paste that is evenly distributed, then it is best to make sure that the pigments you use are enough. The other thing you should do is pull the squeegee well.
Pinholes is also another issue that one is likely to face. Many reasons might lead to pinholes like the mesh might have some gum or oil which are dirty. If you do not want to deal with the pinholes, it is best to wash the mesh so that you can get rid of any impurities. Make sure that the products you are using are clean.
If you do not do the coating right then, this is another reason that you will end up with pinholes. That is the reason that it is advisable to carry out the surface more than ones. That way when you do the final washing on the fabric, the colors will be well distributed, and you will not have to deal with pinholes.
If you notice that the paint is spreading through the areas that you do not want to print, then this is known as bleeding. It is one of the most common mistakes that one might find, and the best way that you can deal with it is making the paste thick. Bleeding comes as a result of using watery paste. It is best to ask someone who has been this for a long time to help you with the mixing of the adhesive.
It is frustrating when you find that you have gaps that are not equal when you are doing repeats. Most people think that doing a repeat is something simple, but that is not the case. If you want to do it right then, you should be calculative. Check well and do calculative placement.
If you are new in this scheme, you might not know where to place the repeats. To deal with this, you need to use colored chalk to mark the repeats on that cloth, and this will help one know where they will be placing each repeat. The other solution is placing of colored strands at the edge of the design and when doing a repeat all one need to do is to put the screen directly on the strands.
The other thing that you should watch out for is soiling of the cloth. Note that if you do not block the pores, then you might end up with this problem. That is the reason that you should apply a tape around the edge; it will make the print clean and well done since there will be no spillage on the sides.
Having the colored pigments not being distributed is also another issue that you might end up facing. If this is the situation, you might end up with the formation of patches. If you want to have a paste that is evenly distributed, then it is best to make sure that the pigments you use are enough. The other thing you should do is pull the squeegee well.
Pinholes is also another issue that one is likely to face. Many reasons might lead to pinholes like the mesh might have some gum or oil which are dirty. If you do not want to deal with the pinholes, it is best to wash the mesh so that you can get rid of any impurities. Make sure that the products you are using are clean.
If you do not do the coating right then, this is another reason that you will end up with pinholes. That is the reason that it is advisable to carry out the surface more than ones. That way when you do the final washing on the fabric, the colors will be well distributed, and you will not have to deal with pinholes.
About the Author:
Find a summary of the advantages you get when you use Maryland screen printing services and more information about a reputable printing company at http://spnprints.com/services.html now.
No comments:
Post a Comment